Report item
Item specifics
  • Product name: CNC Shield Expansion Board kit
  • Condition: New100%
  • Meterial: Aluminum
  • Type: Voltage Regulator
Product Description


CNC Shield Expansion Board V3.0 + UNO R3 Board for Arduino + Stepper Moto Driver A4988 With Heatsink Kits for Arduino

CNC Shield Board:    

1,Latest CNC Shield Version 3.0 for Arduino.    

2,GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals)    

3,PWM Spindle and direction pins    

4,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a  full 4th axis with custom firmware using pins D12 and D13)    

5,2 x End stops for each axis (6 in total)     

6,Coolant enable     

7,Uses removable A4988 or DRV8825 compatible stepper drivers    

8,Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to  1/32 micro-stepping )     

9,Compact design.    

10,Stepper Motors can be connected with 4 pin molex connectors or soldered in place.     

11,Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)    

12,Please note that this is an unassembled kit and Basic soldering skills are needed.    


A4988 Stepper Motor Driver:    


1,A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product.    

Low RDS (On) Output    

2,Automatic current decay mode  detection / selection    

3,Mix with slow current decay modes    

4,Synchronous rectification for low power dissipation    

5,Internal UVLO    

6,Crossover-current protection    

7,3.3 and 5 V compatible logic supply    

8,Thermal shutdown circuitry    

9,Ground fault protection    

10,Load short-circuit protection    

11,Five selectable step modes: full,  1/2, 1/4, 1/8 and 1/16   

UNO R3 Board for Arduino:    

MCU: ATmega328    

USB interface: ATmega16U2    

Operating voltage: 5V    

Digital I/O pins: 14 (including 6  with PWM capability)    

Analog input pins: 6    

I-I/O pin output current: 40mA max    

3.3V output current: 150mA max    

Flash memory: 32kB (0.5kB used by bootloader- included)    

Static RAM (SRAM): 2kB    

EEPROM: 1kB    

Clock speed: 16MHz  

Package Includes:    

1 x CNC Shield Board    

1 x UNO R3 Board for Arduino    

4 x A4988 Stepper Motor Driver    

4 x Heat Sink







    • Payment Method
If you have any trouble with payment ,please contact us . We can accept any payment method you would like to choose .

• Quality Warranty

1.Please contact us if you have any problem of quality .

2.90 Days of quality warranty .

3.Defective items must be returned within the warranty period.
 Feedback is very important for us.We appreciate your positive feedback if you are statisfy with our products and service.
Please contact us before leaving any negative or neutral feedback. We will solve any problem in 24hous.



Packaging Details
  • Unit Type: piece
  • Package Weight: 0.2kg (0.44lb.)
  • Package Size: 10cm x 10cm x 10cm (3.94in x 3.94in x 3.94in)
Calculate your shipping cost by country/region and quantity.
Quantity: Ship to:
Packaging Details
  • Unit Type: piece
  • Package Weight: 0.2kg (0.44lb.)
  • Package Size: 10cm x 10cm x 10cm (3.94in x 3.94in x 3.94in)
We support the following payment methods. All payments made on AliExpress are processed by Alipay.